Jump to content
Printer Reset Forum
John_Admin

Epson Printer Chipless - No Chips Firmware

Recommended Posts

I must say I'm really disapointed. It did not worked for Epson p600. I bought Firmware key and updated printer as described. Printer reported update successful, but nothing has changed, INK levels are as they were before... I would love to get my money back...

Share this post


Link to post
Share on other sites

Update process consists of two steps, first application send firmware data to the printer and signal that transfer is finished, then printer shutdown all communication and start internal update, at this point it`s impossile to check the results. Recently Epson started to block older versions of the firmware with their updates, after checking firmware signature printer just refuses to write data to the chip. If you send me key via PM, I will restore it. After this, you have two options, either use WIC key again with this method that may or may not work:

or replace WIC key with CS key after paying the difference.

  • Thanks 1

Share this post


Link to post
Share on other sites

Mostly yes, after last update printer shows full ink level on all cartridges. But, first print after turning on theprinter is with errors on all of them. I need to open cartridge cover and closed it. After that printer "recognize" cartridges once again and I can print. 

I've read somewhere on this forum that other user had same issue, but I don't recall if this can be fixed or not.

Share this post


Link to post
Share on other sites

lütfen yardım edin 

epson wf 6090  firmware yükledim

atık kutu bitti diyor yeni takıyorum görmüyor

bellenim aldım yükledim 
ama acil durum edin 

https://www.2manuals.com/  burdan aldım 

hdizlet@gmail.com

please help me

I installed epson wf 6090 firmware

the waste bin is finished, I am just wearing it

I got it firmware, I loaded it
but make it urgent

https://www.2manuals.com/ I got it from here

Share this post


Link to post
Share on other sites

Please, install latest official version of the firmware, then replace/reset maintenance box and make sure that it is recognized by the printer, after this install chipless firmware back and reactivate it using recovery code.

Share this post


Link to post
Share on other sites

I have an Epson WF-3730.  I purchased an activation key after successfully updating the firmware(putting printer in recover mode and using the epson update utility linked as described.  When I bring up the license application to activate the firmware I get the error "Unsupported Printer Model".  What is the problem?  I have tried multiple times to write the firmware and each time it was successful.  Help!

Share this post


Link to post
Share on other sites

Hello ~

i have 2 printers  one is EPSON WF-4020 , another is EPSON WF4530

these printers  can be supported for chipless ?

gongcd@hotmail.com

953.png

Share this post


Link to post
Share on other sites

Hello,

I have tried to make my wf-3620 chipless and followed your instructions carefully.

After the firmware downgrade process and using the key I bought, the printer screen said firmware upgrade success.

I pressed 0 to turn off the printer and restarted after a couple of minutes.

The wic reset utility informs me that my firmware version is cc 20 gc, release date 20/12/2016

The ink levels show 100%

But I have a big problem-nothing prints.

I have restarted the printer, performed head cleaning, charged the ink from the wic reset utility, reinstalled the cartridges, tried printing saturated colour bars but no ink appears on the paper.

I have cleaned the print head with Printhead magic solution and alcohol. Liquid flows freely when doing this.

I have tried two different sets of XL cartridges.

Before I tried any firmware changes, I was having trouble with the printer recognising ink levels. Low ink warning of a particular colour resulted in that colour not printing well. This is the reason I tried to go chipless.

Before the firmware change, I always managed to get a print, even if the quality was not the best. Now I can only print blank paper.

So please help me, and advise what i should now try

 

Kind regards,

 

Peter

Share this post


Link to post
Share on other sites

Thankyou wic.support for your response.

I have printed nozzle check pattern and flushed out the printhead a number of times and am finally getting the ink to flow. It seems that my problem was a badly clogged printhead and nothing to do with my firmware downgrade and key. I think you have a wonderful product.

Kind regards,

Peter

Share this post


Link to post
Share on other sites

Hello @John_Admin and @wic.support: I have a Epson XP-15000 that I (stupidly) updated and there is conflicting information if a firmware activation key is available for this model... Within the WIC Reset Utility (v5.59), it looks like the answer is no, but on 2Manuals.com, it clearly states that this machine can indeed go chipless. Any chance you could give me a clear answer and direction on this? I just want to be able to print with the numerous non-OEM cartridges I've invested in. Thank you.

Share this post


Link to post
Share on other sites

Create an account or sign in to comment

You need to be a member in order to leave a comment

Create an account

Sign up for a new account in our community. It's easy!

Register a new account

Sign in

Already have an account? Sign in here.

Sign In Now

×
×
  • Create New...